k2hyun
우분투(ubuntu)에 LBP-3200 프린터 드라이버 설치하기 본문
하지만 아래 방법처럼 하면 프린터 드라이버를 설치할수 있다.
- 참고 사이트 ---------------------------------------------------------------------------------------
1. http://www.stmin2.com/tag/LBP3200
2. https://help.ubuntu.com/community/HardwareSupportComponentsPrinters/CanonPrinters/Canon_LBP_2900
----------------------------------------------------------------------------------------------------
원본에는 모델명이 2900 인데 편의상 3200으로 바꿧다.
amd64 사용자는 amd64Step 부터 보길 바란다. 드라이버도 거기서 링크된 2개의 파일을 다운받아 설치하길 바란다.
invalid-file(혹시 몰라서 파일 첨부함.)
Step 1에 나온 경로에서 최신드라이버 1.6버전이 있는데 본인이 설치할때는 드라이버 셋팅은 되었는데
문서출력 안되었다.(뭘 알야야 손보지;-_-)
Step 1:
Go to the following web page and download the Driver.tar.gz:
http://software.canon-europe.com/products/0010177.asp
Step 2:
Extract Driver.tar.gz either by right-clicking on the file and selecting "Extract Here", or in the Terminal in the directory you downloaded it into and entering the following command:
$ tar -xvf Driver.tar.gz
This should create a new directory called Driver which contains two files: cndrvcups-capt-1.30-1.i386.rpm and cndrvcups-common-1.30-1.i386.rpm.
These rpms need to be converted into debs so that we can install
them, and to do that we need to install alien. You can do that with
Synaptic (System > Administration > Synaptic) or in the Terminal:
처음 rpm을 deb로 작업할때 alien가 필요하니 먼저 설치한다.
$ sudo aptitude install alien
Then, you convert the files using alien in the Terminal:
$ sudo alien -c cndrvcups-capt-1.30-1.i386.rpm
$ sudo alien -c cndrvcups-common-1.30-1.i386.rpm
Install the debs you have just created by double clicking on the files or using the Terminal:
$ sudo dpkg -i cndrvcups-common_1.30-2_i386.deb cndrvcups-capt_1.30-2_i386.deb
Note that the latest version of the drivers contain .deb packages, which you can use instead of the above procedure to convert RPMs.
Step 3:
In order to load the new drivers we have installed we need to stop and restart CUPS. Firstly we stop CUPS:
$ sudo /etc/init.d/cupsys stop
Check that it is stopped. All the times I have done this, CUPS had stopped first time but apparently this may not always be the case due to the installation of ccp:
$ sudo ps ax | grep cupsd
Which will give you something like this:
cupsys 24897 0.0 0.1 4336 1976 ? SNs 07:35 0:04 /usr/sbin/cupsd
username 24738 0.0 0.0 2896 836 pts/0 S+ 21:21 0:00 grep cupsd
If you only get a line that ends with "grep cupsd" CUPS has stopped and you can carry on. If you also get a line that ends with "/usr/sbin/cupsd", as shown above, CUPS has not stopped and you will have to try the following method to stop it:
$ sudo killall cupsd
The aliened debs are not perfect so we have to do some of their the work for them. Create two directories:
나의 경우엔 이미 만들어져 있었다.
$ sudo mkdir /var/ccpd
$ sudo mkdir /var/captmon
And a fifo:
$ sudo mkfifo /var/ccpd/fifo0
Make fifo0 accessable to everyone:
$ sudo chmod 777 /var/ccpd/fifo0
In Ubuntu Edgy and Feisty, change the owner of fifo0 into root (failing to do so gives you an error: Unable to copy PPD file in step 4):
$ sudo chown root /var/ccpd/fifo0
You may need to make the permissions of the /usr/share/cups/model directory more permissive.
$ sudo chmod -R a+rX /usr/share/cups/model
Once you have done this, start CUPS again:
$ sudo /etc/init.d/cupsys start
Step 4:
Register the printer driver with the print spooler with the following command, replacing [printer model] with your printer model and [printer driver file] with your driver file:
$ sudo /usr/sbin/lpadmin -p [printer model] -m [printer driver file] -v ccp:/var/ccpd/fifo0 -E
For example, the command for the Canon LBP 3200 would be:
$ sudo /usr/sbin/lpadmin -p LBP3200 -m CNCUPSLBP3200CAPTK.ppd -v ccp:/var/ccpd/fifo0 -E
Note: If you get the error lpadmin: Unable to copy PPD file!, try substituting -P for -m above.
If you are unsure of what your driver file is called you can get a list of the available drivers:
$ ls /usr/share/cups/model/ | grep CNCUPS
Look for the one that matches your model number. Some of them end with "K.ppd" and some end with "J.ppd". I have no idea what difference is, the K ones have worked fine for me so far.
Added 2007-12-09: for me, under Ubuntu 7.10, the K ones constantly use about 75% CPU, while the J ones don't. I did not find any problems with the J file so far.
Ubuntu Edgy and Feisty are searching the driver in /usr/share/ppd/ so I created a link:
$ cd /usr/share/ppd/
$ sudo ln -s /usr/share/cups/model/CNCUPSLBP3200CAPTK.ppd
Once registered your printer should appear in the System > Administration > Printing dialog.
Register the printer with ccpd daemon, once again replace [printer model] with your printer model:
$ sudo /usr/sbin/ccpdadmin -p [printer model] -o /dev/usblp0
For example, the command for the Canon LBP 3200 would be:
$ sudo /usr/sbin/ccpdadmin -p LBP3200 -o /dev/usblp0
Step 5:
Replace /etc/init.d/ccpd with the script below (taken from http://rdoursenaud.free.fr/debian/capt.html):
#!/bin/sh#
# ccpd startup script for Canon Printer Daemon for CUPS
#
# Modified for Debian GNU/Linux
# by Raphael Doursenaud <rdoursenaud@free.fr>.
DAEMON=/usr/sbin/ccpd
LOCKFILE=/var/lock/subsys/ccpd
PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin
NAME=ccpd
DESC="Canon Printer Daemon for CUPS"
test -f $DAEMON || exit 0
case $1 in
start)
echo -n "Starting $DESC: $NAME"
start-stop-daemon --start --quiet --exec $DAEMON
echo "."
;;
stop)
echo -n "Stopping $DESC: $NAME"
start-stop-daemon --stop --quiet --oknodo --exec $DAEMON
echo "."
;;
status)
echo "$DESC: $NAME:" `pidof $NAME`
;;
restart)
echo -n "Restarting $DESC: $NAME"
start-stop-daemon --stop --quiet --oknodo --exec $DAEMON
sleep 1
start-stop-daemon --start --quiet --exec $DAEMON
echo "."
;;
*)
echo "Usage: ccpd {start|stop|status}"
exit 1
;;
esac
exit 0
Copy and paste the above script into a new text file, then backup and replace the old version:
만일의 경우를 대비해 백업을 합니다.
다음 위 스크립트를 복사한후 편집기를 열어서 붙혀넣기 하면 됩니다.
$ sudo mv /etc/init.d/ccpd ccpdold
$ sudo vim /etc/init.d/ccpd
* vim 에서 입력을 다했다면 저장하고 나오는 명령어는 Esc 키를 누르고나서 : 입력후 wq 를 입력하면된다.
Give everyone execution rights to the new file:
$ sudo chmod a+x /etc/init.d/ccpd
Step 6:
Start the ccpd daemon:
$ sudo /etc/init.d/ccpd start
Step 7:
Set ccpd to start when you startup your computer:
$ sudo update-rc.d ccpd defaults 20
Step 8:
프린터 전원을 끄고 컴퓨터를 재시작한다.
Switch off the printer and reboot your computer. Once you have logged in, switch on the printer again.
Step 9:
잘 설치되었는지 확인한다.
Test your installation.
First test:
$ sudo ccpdadmin
Which should output this:
Usage:
ccpdadmin [-p Printer-name -o Printer-dev-path]
ccpdadmin [-x Remove-Printer-name]
CUPS_ConfigPath = /etc/cups/
LOG Path = None
UI Port = 39787
Entry Num : Spooler : Backend : FIFO path : Device Path : Status
----------------------------------------------------------------------------
[0] : LBP3200 : ccp : /var/ccpd/fifo0 : /dev/usblp0 :
Second test, replace [printer model] with your printer model
$ captstatusui -P [printer model]
For example, the command for the Canon LBP 3200 would be:
$ captstatusui -P LBP3200
프린터 사용준비가 완료되었다.
This will launch a window that after a bit should say "ready to print".
Finally open a file and try to print it.
amd64 Steps:
amd64 사용자는 아래 파일을 먼저 다운받아서 설치하기바란다.
First thank you for this wonderful info! Following it I managed to install LBP-1210 on Ubuntu 6.10 Edgy amd64! I taught it would be impossible, but it WORKS!
Before you start this procedure:
- I had to install following ia32 libraries in my Edgy amd64 distribution, I did this using Synaptic, installed; ia32-libs, ia32-libs-gtk, ia32-kde (don't know if this one is really needed), ia32-libs-openoffice.org. I also installed some other 32-bit packages, just in case, and for the need of some other 32-bit software such as Skype; lib32asaund2, lib32gcc1, lib32stdc++6 and lib32z1
Feisty amd64 distribution does not have ia32-libs-openoffice.org in its repositories! One option is to download Edgy's ia32-libs-openoffice.org package from here, and to install it manually. Another option is to extract some libraries manually from Feisty x86 packages and to place them in /usr/lib32/. These packages are; libtasn1-3, libgcrypt11 and libgpg-error0, with respective libraries.
Also, during regular installation steps, Canon's driver required libcups.so.2 and libgnutls.so.13 32-bit libraries which I had to provide manually because they were not included in any of standard amd64 ia32* or lib32* packages (funny that libgnutls.so.12 is included in ia32-libs-openoffice.org Edgy amd64 package). I copied these libcups.so.2 and libgnutls.so.13 from 32-bit Ubuntu Dapper Distribution to /usr/lib32. You can also copy this library from chroot 32-bit distribution if you have one.
- Also you can download and extract manually this file from standard 32-bit packages, it is libcupsys2 and libgnutls packages. It can be found here and here.
- You can see how to setup chroot environment here.
After you start install procedure:
- In Step 2, when you should convert these 32-bit Cannon drivers packages using alien, it will probably not work using 64-bit alien. I had to use 32-bit Dapper chroot distribution I had set up previously. From chroot, alien converting worked fine, using same commands. For your convenience, some debs are attached below.
Again, in Step 2 one should use --force-architecture install option when trying to install these 32-bit driver packages on 64-bit machine. Do this at your own risk. It installed for me without problem, with few warnings only.
Testing your printer
- In Step 9, following test might not work (replace [printer model] with your printer model):
$ captstatusui -P [printer model]
- This should launch a window that should say "ready to print" or something, but in my system it required more 32-libraries... If you really need this useless status window, extract libgtk-1.2, libgdk-1.2, libglib-1.2 and libgmodule-1.2 libraries from libgtk1.2 and libglib1.2 Feisty or Edgy packages and place them into /usr/lib32/. Try right-clicking you printer in System > Administration > Printing dialog, and opening Properties. Print test page should work without problems.
Note: I tested this only on my Canon LBP-1210 printer connected to USB. My computer doesn't have Parallel port so I could not test it. Other printers mentioned at top of this page should work as well.
This did not work for me on an IA32 (Duron 750MHz) machine attached via parallel port. I replaced usblp0 with lp0, but instead of saying "ready to print" it had nothing in the message box.